Specification
| Parameter | Unit | T 115 3 21 | T 115 3 15 | T 115 5,2 14 | T 115 5,2 15 | T 115 7 15 | T 115 7 17 | T 115 9,2 15 | T 115 9,2 17 | T 115 11 15 | T 115 11 17 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Continuous stall torque | Nm | 3 | 3 | 5 | 5 | 6.5 | 6.5 | 8.5 | 8.5 | 9.5 | 9.5 |
| Maximum working speed 24VDC | rpm | 5000 | 3900 | 5000 | 3900 | 3900 | 2200 | – | – | – | – |
| Maximum working speed 230VAC | rpm | – | – | – | – | – | – | 3900 | 2200 | 3900 | 2200 |
| Maximum working speed 400VAC | – | 5000 | – | 5000 | 4500 | 3900 | 4500 | 3900 | 4500 | 3900 | |
| Torque Constant | Nm/Arms | 0.53 | 0.91 | 0.6 | 0.91 | 0.91 | 1.6 | 0.91 | 1.6 | 0.91 | 1.6 |
| Voltage constant | Vrms/Krpm | 31.8 | 55 | 36 | 55 | 55 | 97 | 55 | 97 | 55 | 97 |
| Winding resistance | Ω | 1.3 | 4 | 0.9 | 2.1 | 1.2 | 3.7 | 0.9 | 2.8 | 0.9 | 2.8 |
| Winding inductance | mH | 3 | 9 | 2.4 | 6.1 | 4.1 | 12 | 3.1 | 10 | 2.9 | 8.6 |
| Electrical time constant | ms | 2.3 | 2.3 | 2.7 | 2.9 | 3.4 | 3.2 | 3.4 | 3.6 | 3.2 | 3.1 |
| Thermal resistance | °C/W | 1.08 | 1.05 | 0.72 | 0.72 | 0.74 | 0.75 | 0.58 | 0.58 | 0.45 | 0.46 |
| Mechanical timeconstant, high rotor inertia | ms | 5.1 | 5.3 | 4 | 4 | 3.1 | 3 | 2.9 | 2.9 | 3.5 | 3.4 |
| Peak Torque | Nm | 9 | 9 | 15.6 | 15.6 | 21 | 21 | 27.6 | 27.6 | 33 | 33 |
| Mechanical time constant, low rotor inertia | ms | 5.3 | 3.4 | 2.6 | 2.6 | 1.9 | 1.9 | 1.8 | 1.8 | 2.2 | 2.1 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 7.3 | 7.3 | 10.6 | 10.6 | 14.1 | 14.1 | 17.5 | 17.5 | 20.8 | 20.8 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | 4.7 | 4.7 | 6.8 | 6.8 | 8.8 | 8.8 | – | – | – | – |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | – | – | – | – | – | – | 10.9 | 10.9 | 13 | 13 |
| Mass without holding brake | Kg | 4.7 | 4.7 | 6.2 | 6.2 | 7.5 | 7.5 | 8.8 | 8.8 | 9.9 | 9.9 |
| Mass with holding brake | Kg | 5.9 | 5.9 | 7.4 | 7.4 | 8.7 | 8.7 | 9.9 | 9.9 | 11.7 | 11.7 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 | 180 | 180 | 180 | 180 | 180 | 180 | 180 | 180 | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 | 600 | 600 | 600 | 600 | 600 | 600 | 600 | 600 | 600 |
| Motor length (without brake) | mm | 164 | 164 | 189 | 189 | 214 | 214 | 239 | 239 | 264 | 264 |
| Motor length (with brake) | mm | 214 | 214 | 239 | 239 | 264 | 264 | 289 | 289 | 314 | 314 |
| Nominal torque | Nm | 2.7 | 2.7 | 4.1 | 4.1 | 5.3 | 5.3 | 6.4 | 6.4 | 7.3 | 7.3 |
| Rated voltage | V | 230 | 400 | 230 | 400 | 230 | 400 | 230 | 400 | 230 | 400 |
| Nominal power | W | 840 | 840 | 1300 | 1300 | 1650 | 1650 | 2000 | 2000 | 2300 | 2300 |
| Continuous stall current | Arms | 5.7 | 3.3 | 8.4 | 5.5 | 7.1 | 4.1 | 9.3 | 5.3 | 10.4 | 5.9 |
| Maximun Current | Arms | 17.1 | 9.9 | 26.2 | 17.1 | 23.1 | 13.1 | 30.3 | 17.2 | 36.3 | 20.6 |
| Nominal current | Arms | 5.3 | 3.1 | 7.3 | 4.8 | 6.1 | 3.4 | 7.3 | 4.2 | 8.5 | 4.8 |
| Nominal speed | rpm | 3000 | 3000 | 3000 | 3000 | 3000 | 3000 | 3000 | 3000 | 3000 | 3000 |
Family Specification
| Family Specification | Unit | TC 115 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | TC 115 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 3 21 |
|---|---|---|
| Continuous stall torque | Nm | 3 |
| Maximum working speed 24VDC | rpm | 5000 |
| Maximum working speed 230VAC | rpm | – |
| Maximum working speed 400VAC | – | |
| Torque Constant | Nm/Arms | 0.53 |
| Voltage constant | Vrms/Krpm | 31.8 |
| Winding resistance | Ω | 1.3 |
| Winding inductance | mH | 3 |
| Electrical time constant | ms | 2.3 |
| Thermal resistance | °C/W | 1.08 |
| Mechanical timeconstant, high rotor inertia | ms | 5.1 |
| Peak Torque | Nm | 9 |
| Mechanical time constant, low rotor inertia | ms | 5.3 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 7.3 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | 4.7 |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | – |
| Mass without holding brake | Kg | 4.7 |
| Mass with holding brake | Kg | 5.9 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 164 |
| Motor length (with brake) | mm | 214 |
| Nominal torque | Nm | 2.7 |
| Rated voltage | V | 230 |
| Nominal power | W | 840 |
| Continuous stall current | Arms | 5.7 |
| Maximun Current | Arms | 17.1 |
| Nominal current | Arms | 5.3 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 3 21 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 3 21 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 3 15 |
|---|---|---|
| Continuous stall torque | Nm | 3 |
| Maximum working speed 24VDC | rpm | 3900 |
| Maximum working speed 230VAC | rpm | – |
| Maximum working speed 400VAC | 5000 | |
| Torque Constant | Nm/Arms | 0.91 |
| Voltage constant | Vrms/Krpm | 55 |
| Winding resistance | Ω | 4 |
| Winding inductance | mH | 9 |
| Electrical time constant | ms | 2.3 |
| Thermal resistance | °C/W | 1.05 |
| Mechanical timeconstant, high rotor inertia | ms | 5.3 |
| Peak Torque | Nm | 9 |
| Mechanical time constant, low rotor inertia | ms | 3.4 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 7.3 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | 4.7 |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | – |
| Mass without holding brake | Kg | 4.7 |
| Mass with holding brake | Kg | 5.9 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 164 |
| Motor length (with brake) | mm | 214 |
| Nominal torque | Nm | 2.7 |
| Rated voltage | V | 400 |
| Nominal power | W | 840 |
| Continuous stall current | Arms | 3.3 |
| Maximun Current | Arms | 9.9 |
| Nominal current | Arms | 3.1 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 3 15 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 3 15 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 5,2 14 |
|---|---|---|
| Continuous stall torque | Nm | 5 |
| Maximum working speed 24VDC | rpm | 5000 |
| Maximum working speed 230VAC | rpm | – |
| Maximum working speed 400VAC | – | |
| Torque Constant | Nm/Arms | 0.6 |
| Voltage constant | Vrms/Krpm | 36 |
| Winding resistance | Ω | 0.9 |
| Winding inductance | mH | 2.4 |
| Electrical time constant | ms | 2.7 |
| Thermal resistance | °C/W | 0.72 |
| Mechanical timeconstant, high rotor inertia | ms | 4 |
| Peak Torque | Nm | 15.6 |
| Mechanical time constant, low rotor inertia | ms | 2.6 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 10.6 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | 6.8 |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | – |
| Mass without holding brake | Kg | 6.2 |
| Mass with holding brake | Kg | 7.4 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 189 |
| Motor length (with brake) | mm | 239 |
| Nominal torque | Nm | 4.1 |
| Rated voltage | V | 230 |
| Nominal power | W | 1300 |
| Continuous stall current | Arms | 8.4 |
| Maximun Current | Arms | 26.2 |
| Nominal current | Arms | 7.3 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 5,2 14 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 5,2 14 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 5,2 15 |
|---|---|---|
| Continuous stall torque | Nm | 5 |
| Maximum working speed 24VDC | rpm | 3900 |
| Maximum working speed 230VAC | rpm | – |
| Maximum working speed 400VAC | 5000 | |
| Torque Constant | Nm/Arms | 0.91 |
| Voltage constant | Vrms/Krpm | 55 |
| Winding resistance | Ω | 2.1 |
| Winding inductance | mH | 6.1 |
| Electrical time constant | ms | 2.9 |
| Thermal resistance | °C/W | 0.72 |
| Mechanical timeconstant, high rotor inertia | ms | 4 |
| Peak Torque | Nm | 15.6 |
| Mechanical time constant, low rotor inertia | ms | 2.6 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 10.6 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | 6.8 |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | – |
| Mass without holding brake | Kg | 6.2 |
| Mass with holding brake | Kg | 7.4 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 189 |
| Motor length (with brake) | mm | 239 |
| Nominal torque | Nm | 4.1 |
| Rated voltage | V | 400 |
| Nominal power | W | 1300 |
| Continuous stall current | Arms | 5.5 |
| Maximun Current | Arms | 17.1 |
| Nominal current | Arms | 4.8 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 5,2 15 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 5,2 15 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 7 15 |
|---|---|---|
| Continuous stall torque | Nm | 6.5 |
| Maximum working speed 24VDC | rpm | 3900 |
| Maximum working speed 230VAC | rpm | – |
| Maximum working speed 400VAC | 4500 | |
| Torque Constant | Nm/Arms | 0.91 |
| Voltage constant | Vrms/Krpm | 55 |
| Winding resistance | Ω | 1.2 |
| Winding inductance | mH | 4.1 |
| Electrical time constant | ms | 3.4 |
| Thermal resistance | °C/W | 0.74 |
| Mechanical timeconstant, high rotor inertia | ms | 3.1 |
| Peak Torque | Nm | 21 |
| Mechanical time constant, low rotor inertia | ms | 1.9 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 14.1 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | 8.8 |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | – |
| Mass without holding brake | Kg | 7.5 |
| Mass with holding brake | Kg | 8.7 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 214 |
| Motor length (with brake) | mm | 264 |
| Nominal torque | Nm | 5.3 |
| Rated voltage | V | 230 |
| Nominal power | W | 1650 |
| Continuous stall current | Arms | 7.1 |
| Maximun Current | Arms | 23.1 |
| Nominal current | Arms | 6.1 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 7 15 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 7 15 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 7 17 |
|---|---|---|
| Continuous stall torque | Nm | 6.5 |
| Maximum working speed 24VDC | rpm | 2200 |
| Maximum working speed 230VAC | rpm | – |
| Maximum working speed 400VAC | 3900 | |
| Torque Constant | Nm/Arms | 1.6 |
| Voltage constant | Vrms/Krpm | 97 |
| Winding resistance | Ω | 3.7 |
| Winding inductance | mH | 12 |
| Electrical time constant | ms | 3.2 |
| Thermal resistance | °C/W | 0.75 |
| Mechanical timeconstant, high rotor inertia | ms | 3 |
| Peak Torque | Nm | 21 |
| Mechanical time constant, low rotor inertia | ms | 1.9 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 14.1 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | 8.8 |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | – |
| Mass without holding brake | Kg | 7.5 |
| Mass with holding brake | Kg | 8.7 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 214 |
| Motor length (with brake) | mm | 264 |
| Nominal torque | Nm | 5.3 |
| Rated voltage | V | 400 |
| Nominal power | W | 1650 |
| Continuous stall current | Arms | 4.1 |
| Maximun Current | Arms | 13.1 |
| Nominal current | Arms | 3.4 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 7 17 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 7 17 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 9,2 15 |
|---|---|---|
| Continuous stall torque | Nm | 8.5 |
| Maximum working speed 24VDC | rpm | – |
| Maximum working speed 230VAC | rpm | 3900 |
| Maximum working speed 400VAC | 4500 | |
| Torque Constant | Nm/Arms | 0.91 |
| Voltage constant | Vrms/Krpm | 55 |
| Winding resistance | Ω | 0.9 |
| Winding inductance | mH | 3.1 |
| Electrical time constant | ms | 3.4 |
| Thermal resistance | °C/W | 0.58 |
| Mechanical timeconstant, high rotor inertia | ms | 2.9 |
| Peak Torque | Nm | 27.6 |
| Mechanical time constant, low rotor inertia | ms | 1.8 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 17.5 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | – |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | 10.9 |
| Mass without holding brake | Kg | 8.8 |
| Mass with holding brake | Kg | 9.9 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 239 |
| Motor length (with brake) | mm | 289 |
| Nominal torque | Nm | 6.4 |
| Rated voltage | V | 230 |
| Nominal power | W | 2000 |
| Continuous stall current | Arms | 9.3 |
| Maximun Current | Arms | 30.3 |
| Nominal current | Arms | 7.3 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 9,2 15 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 9,2 15 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 9,2 17 |
|---|---|---|
| Continuous stall torque | Nm | 8.5 |
| Maximum working speed 24VDC | rpm | – |
| Maximum working speed 230VAC | rpm | 2200 |
| Maximum working speed 400VAC | 3900 | |
| Torque Constant | Nm/Arms | 1.6 |
| Voltage constant | Vrms/Krpm | 97 |
| Winding resistance | Ω | 2.8 |
| Winding inductance | mH | 10 |
| Electrical time constant | ms | 3.6 |
| Thermal resistance | °C/W | 0.58 |
| Mechanical timeconstant, high rotor inertia | ms | 2.9 |
| Peak Torque | Nm | 27.6 |
| Mechanical time constant, low rotor inertia | ms | 1.8 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 17.5 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | – |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | 10.9 |
| Mass without holding brake | Kg | 8.8 |
| Mass with holding brake | Kg | 9.9 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 239 |
| Motor length (with brake) | mm | 289 |
| Nominal torque | Nm | 6.4 |
| Rated voltage | V | 400 |
| Nominal power | W | 2000 |
| Continuous stall current | Arms | 5.3 |
| Maximun Current | Arms | 17.2 |
| Nominal current | Arms | 4.2 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 9,2 17 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 9,2 17 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 11 15 |
|---|---|---|
| Continuous stall torque | Nm | 9.5 |
| Maximum working speed 24VDC | rpm | – |
| Maximum working speed 230VAC | rpm | 3900 |
| Maximum working speed 400VAC | 4500 | |
| Torque Constant | Nm/Arms | 0.91 |
| Voltage constant | Vrms/Krpm | 55 |
| Winding resistance | Ω | 0.9 |
| Winding inductance | mH | 2.9 |
| Electrical time constant | ms | 3.2 |
| Thermal resistance | °C/W | 0.45 |
| Mechanical timeconstant, high rotor inertia | ms | 3.5 |
| Peak Torque | Nm | 33 |
| Mechanical time constant, low rotor inertia | ms | 2.2 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 20.8 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | – |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | 13 |
| Mass without holding brake | Kg | 9.9 |
| Mass with holding brake | Kg | 11.7 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 264 |
| Motor length (with brake) | mm | 314 |
| Nominal torque | Nm | 7.3 |
| Rated voltage | V | 230 |
| Nominal power | W | 2300 |
| Continuous stall current | Arms | 10.4 |
| Maximun Current | Arms | 36.3 |
| Nominal current | Arms | 8.5 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 11 15 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 11 15 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.
PDF Downloads
TC 115
datasheet
| Parameter | Unit | T 115 11 17 |
|---|---|---|
| Continuous stall torque | Nm | 9.5 |
| Maximum working speed 24VDC | rpm | – |
| Maximum working speed 230VAC | rpm | 2200 |
| Maximum working speed 400VAC | 3900 | |
| Torque Constant | Nm/Arms | 1.6 |
| Voltage constant | Vrms/Krpm | 97 |
| Winding resistance | Ω | 2.8 |
| Winding inductance | mH | 8.6 |
| Electrical time constant | ms | 3.1 |
| Thermal resistance | °C/W | 0.46 |
| Mechanical timeconstant, high rotor inertia | ms | 3.4 |
| Peak Torque | Nm | 33 |
| Mechanical time constant, low rotor inertia | ms | 2.1 |
| High rotor inertia (as an option) without brake and without feedback | kg·cm² | 20.8 |
| Low rotor inertia (as an option) without brake and without feedback | kg·cm² | – |
| Low rotor inertia (standard) without brake and without feedback | kg·cm² | 13 |
| Mass without holding brake | Kg | 9.9 |
| Mass with holding brake | Kg | 11.7 |
| Maximum axial shaft load applied on the shaft’s center | N | 180 |
| Maximun radial shaft load applied on the shaft’s center | N | 600 |
| Motor length (without brake) | mm | 264 |
| Motor length (with brake) | mm | 314 |
| Nominal torque | Nm | 7.3 |
| Rated voltage | V | 400 |
| Nominal power | W | 2300 |
| Continuous stall current | Arms | 5.9 |
| Maximun Current | Arms | 20.6 |
| Nominal current | Arms | 4.8 |
| Nominal speed | rpm | 3000 |
Family Specification
| Family Specification | Unit | T 115 11 17 |
|---|---|---|
| Time Rating | Continuous | |
| Certification | CE | |
| Recommendation | Rated output with 350 x 350 x 20 mm metallic heat sink flange coupling – Derating must be considered if the oil seal is applied – IP 54 standard shaft bushing | |
| Insulation Class | F | |
| Enclosure | Totally enclosed. Self-cooled | |
| Protection Class | IP 65 standard on the body | |
| Insulation System UL/CSA | cURus , DV155J File nr. : E216686 | |
| Ambient Temperature | °C | 0 to 40 |
| Ambient Humidity | % | 5 to 85% (non-condensing) |
| Poles | 6 | |
| Thermal Protection | PT 1000 |
Family Overview
| Family Overview | Unit | T 115 11 17 |
|---|---|---|
| Flange dimensions | mm | 115 |
| Rated Output Power | Watt | 840 – 2300 |
| Rated Torque | Nm | 2,7 – 7,3 |
| Rated Speed | rpm | 3000 |
Applications
Medical
Biomedical
Agriculture
Processing & Packaging
Logistic & Intralogistic
Technical specifications are for guidance only, as the individual drives and motors are configured for specific applications. Subject to technical and visual changes.